Cattani AC300 – Compresseur dentaire sans huile 3 cylindres – vue 2

AC 300 – Three-cylinder compressor, with air drier

Information intended for dental healthcare professionals.

Technical data (Cattani)

Rated voltage	230 V — (230V 50Hz 1~)
Supply voltage with drier	AC 300 - 3 cylinder compressor with air dryer (230V / 50Hz 1˜) (400V / 50Hz 3˜) (220V / 60Hz 1˜)
Rated frequency	50 Hz — (230V 50Hz 1~)
Supply phases	1
Rated power 220v 60hz single phase	1,75 kW
Rated power 230v 50hz single phase	1,5 kW
Rated power 240v 50hz single phase	1,5 kW
Rated power 400v 50hz three phase	1,5 kW
Rated current 220v 60hz single phase	12,2 A
Rated current 230v 50hz single phase	10,2 A
Rated current 240v 50hz single phase	9,2 A
Rated current 400v 50hz three phase	3,7 A
Air output at 5 bar	238 N l/min
Air output per cylinder	Each cylinder of the compressor produces approximately 60 l/min air at about 5 bar pressure
Air tank	45 l
Dried air enters tank	L'air, ainsi desséché et filtré hygiéniquement, entre dans le réservoir (M) pour être utilisé — L’air, ainsi desséché et filtré hygiéniquement, entre dans le réservoir (M) pour être utilisé.
Tank internal coating	The inside of the tank is painted with a resin approved for food contact and having antibacterial properties, to ensure good preservation of the air
Sound pressure level with canalized air	73.6 dB(A) — Sound pressure level: 73.6 dB (A).
Sound pressure level in sound cabinet	52 dB(A) — Sound-Reducing Cabinet: W840 D700 H887 (mm) Noise Level: 52dB(A)
Sound pressure level measurement	Sound pressure level detected according to ISO 3746-1979 (E); parameters: d = 1.5, background noise <38 dB(A), instrument Bruel & Kjaer type 2232 — Sound pressure level detected according to ISO 3746-1979 (E). Parameters: d = 1.5 - background noise <38 dB(A) - instrument Bruel & Kjaer type 2232.
Sound pressure level measurement distance	1,5 m
Sound pressure level	68 dB(A) — Sound pressure level: 68 dB (A).
Width	620 mm
Width with cover and drier	720 mm
Width with cover without drier	720 mm
Width with drier	620 mm
Width without drier	620 mm
Depth	520 mm
Depth with cover and drier	600 mm
Depth with cover without drier	580 mm

Indications and sizing

Sizing instrument consumption : It is capable of supplying an instrument with about 50/60 l/min* consumption at 2/3 bar pressure. (Source : COMPRESSEUR SANS HUILE À 1-2-3 CYLINDRES, p. 11)
Sizing model selection basis : The selection of the oil free compressor model is made in reference to the compressed air requirements. (Source : COMPRESSEUR SANS HUILE À 1-2-3 CYLINDRES, p. 11)
Suggested number of surgeries : AC300 3 cylinder - up to 4 surgeries (running simultaneously) (Source : Oil-Less Compressors Brochure (Cattani ESAM UK), p. 3)

Installation

Installation air conditioning : Air conditioning may be an option dependent on the size and position of the plant area. (Source : Oil-Less Compressors Brochure (Cattani ESAM UK), p. 4)
Installation airline routing : It is most important that the airline is designed and routed correctly to ensure the airflow is distributed evenly to all surgeries. (Source : Oil-Less Compressors Brochure (Cattani ESAM UK), p. 4)
Installation clean pipework before start : Before starting the machines make sure that the distribution pipe work is clean internally as heavy debris can damage the equipment. (Source : COMPRESSEUR SANS HUILE À 1-2-3 CYLINDRES, p. 12)
Installation closed loop piping : A closed loop system keeps the pressure constant as configured for use. (Source : COMPRESSEUR SANS HUILE À 1-2-3 CYLINDRES, p. 11)
Installation commissioning tests : After the installation, the technician shall perform the regulatory and functional tests and check direction of motor rotation. Mains voltage and electrical absorption shall also be tested. (Source : COMPRESSEUR SANS HUILE À 1-2-3 CYLINDRES, p. 12)
Installation dispose of packaging : Éliminer le carton d’emballage dans le respect des normes en vigueur. (Source : COMPRESSEUR SANS HUILE À 1-2-3 CYLINDRES, p. 9)
Installation earth connection : Earth connections are mandatory for both single and three phase machines. (Source : COMPRESSEUR SANS HUILE À 1-2-3 CYLINDRES, p. 12)
Installation floor drain : Installation of a floor waste connected to the sewer for any possible liquid spillage is recommended. (Source : COMPRESSEUR SANS HUILE À 1-2-3 CYLINDRES, p. 12)
Installation handling equipment : À l’exception des modèles les plus petits, tous les autres compresseurs doivent être déplacés avec des équipements adaptés. (Source : COMPRESSEUR SANS HUILE À 1-2-3 CYLINDRES, p. 15)
Installation handling handles : The compressor is equipped with handles for safe handling. (Source : COMPRESSEUR SANS HUILE À 1-2-3 CYLINDRES, p. 15)
Installation lift by handles only : En tout état de cause, pour un transport en toute sécurité (à la main ou par gerbeur) ne soulever le compresseur qu’à l’aide des poignées. (Source : COMPRESSEUR SANS HUILE À 1-2-3 CYLINDRES, p. 15)
Installation no extension cords : Do not use extension cords or multiple sockets to connect power to the appliance. Plug the appliance power cord directly into the power outlet socket. (Source : COMPRESSEUR SANS HUILE À 1-2-3 CYLINDRES, p. 9)

User maintenance

Consumable hepa h14 filter cartridges : HEPA H14 replacement filter cartridges are provided with fitting and maintenance instructions. (Source : COMPRESSEUR SANS HUILE À 1-2-3 CYLINDRES, p. 14)
Consumable intake filter hepa h14 : Antibacterial filter Hepa H14 item 168429 (10) (Source : Manutenzione straordinaria aspiratori e compressori, p. 2)
Maintenance 12 months bearings : Check (preferably by means of a vibrometer) the good conditions of the bearings (12)***. (Source : Manutenzione straordinaria aspiratori e compressori, p. 2)
Maintenance 12 months charging time : Verify the charging time (from 6 to 8 bar = 45-50 sec.) (Source : Manutenzione straordinaria aspiratori e compressori, p. 2)
Maintenance 12 months drying column : Check the functioning of the drying column and of the moisture drainage electrovalve (8) (Source : Manutenzione straordinaria aspiratori e compressori, p. 2)
Maintenance 12 months head filters : In clean air environments*, clean with compressed air the head filters** - replace them every 12 months (10) (Source : Manutenzione straordinaria aspiratori e compressori, p. 2)
Maintenance 12 months intercooler fans : Check the functioning of intercooler fans (9) (Source : Manutenzione straordinaria aspiratori e compressori, p. 2)
Maintenance 12 months tank drain check : Open the drain screw at the bottom of the reservoir tank. Ensure that only dry air is being expelled, than close the drain screw (11) (Source : Manutenzione straordinaria aspiratori e compressori, p. 2)
Maintenance bearing replacement : It is necessary to use specific tools to replace the bearings, this is why we recommend to send the heads back to Cattani. (Source : Manutenzione straordinaria aspiratori e compressori, p. 2)
Maintenance check capacitor : Check the capacitor capacity (-5% max) (Source : Manutenzione straordinaria aspiratori e compressori, p. 2)
Maintenance check fans : Check the functioning of ventilators (5) (Source : Manutenzione ordinaria aspiratori e compressori, p. 2)
Maintenance check room temperature : Check temperature in the plant room (it must be between + 5 °C and + 35 °C) (Source : Manutenzione ordinaria aspiratori e compressori, p. 2)